What is a PCB Design Floorplan?

October 9, 2014 in Design Tips

What is a PCB Design “Floorplan”?

By Nick Barbin, President of Optimum Design Associates

Oct 09, 2014

A “floorplan” is a drawing that indicates general areas where blocks of circuitry are to be placed on the board. These areas are called “rooms.” Floorplans bridge the gap between the schematic drawing and the physical layout. This gives the designer a head start on placement. Read more:

Flexible Circuit Design Tips: Flex Circuits vs. Traditional PCBs

Flexible Circuit Design Tips: Flex Circuits vs. Traditional PCBs

October 8, 2014 in Design Tips

Flex Circuit design vs. PCB

Flexible circuits still only account for about 15% of the overall printed circuit market. So it’s understandable that there are still questions about flexible circuit design vs. traditional printed circuit board (PCB) design. PCBs have been in existence since the early 1960s and there are many experienced PCB designers working confidently around the world. However we frequently are queried about the nuances in design for flex.

Designers are warned by management, project engineers etc… That flexible circuit design is different and are asked to consult with the fabricator or in some cases simply want to offload the design responsibilities to the supplier.

It’s not that difficult and adding this knowledge to your experience tool box isn’t as daunting a task as it may seem.

 

Similarities and differences

PCB design rules are well known. There are minimum hole sizes, minimum trace width, minimum space between traces and pads. We know to keep copper geometries a certain distance away from the routed edges. We know about hole size and outline tolerances, copper and board thicknesses and myriad other specifications that we don’t even think about any more because it has become an inherent part of our thought process.

Flexible circuit design rules are very similar!  We must pay attention to all of the same issues, minimum hole sizes, minimum trace/space specifications, distance to edge and tolerances.

First let’s discuss the fabrication process. Traditional PCBs and flex are fabricated in much the same way for the first several steps. The flex material, typically copper clad polyimide, is allocated, drilled, plated, imaged, developed and etched just as printed circuit boards are. The next step however is where the changes occur. The panels must be baked as are PCBs to remove moisture from the wet processes, then however where a PCB would go to a solder mask station, flex circuits go to a cover layer station.

The insulating layer of a flexible circuit is made of polyimide the majority of the time. This is not a screen process as it is in PCB fabrication, it is a lamination process. Therefore the rules for oversize of openings are a little different.

The cover layer material is made of 1 mil thick polyimide with a 1 mil thick adhesive attached. The material is drilled to create the openings and so the tolerances of drill location and size apply.

Also during the lamination process the adhesive is heated to a temperature that allows the adhesive to flow easily. It must fill in all of the gaps between traces and pads so that there is no air trapped between layers. What this means to a flexible circuit designer is that the cover layer openings for a typical 1 oz copper design needs to be oversized by .010” (10 mils). This is significantly larger than the typical PCB solder mask which oversize’s 2-3 mils. The reason is first the tolerance of drill size and location, but also to account for the adhesive which squeezes out into the openings. We want to design such that the adhesive flows out to the pad, but not on top of the pad. That would affect the size of the annular ring. We call this phenomenon squeeze out and we want it to dam up on the thickness of the copper pad and not flow over the dam.

Another area we must worry about that isn’t common with PCBs is the “flex area”. Some reasons for using flexible circuits are simply size and weight, but many of the applications take advantage of the flexibility and use the circuit in this manner. There are two typical ways this is done. Flex to fit: The circuit is flexed once only to fit into the assembly and Dynamic flex: This circuit will not only flex to fit into the assembly, but will be dynamic during operation. Either scenario requires a bit of thought be put into the trace routing and pad placement in that area. First it’s best not to have any components (solder pads) in this area. Whether the flex is formed once for fit or dynamic, the solder joint still will be the weakest part of the circuit. Solder, RoHS or leaded, is rigid and not intended to bend, flex or twist. Therefore if those joints are in the flex area you will likely see fractured solder joint at some point. It’s best to keep all solder points at least .100” (100 mils) away from flex areas. Further is better if real estate allows.

Traces should route through the flex areas perpendicularly. This allows us to take advantage of the malleability of the copper. Rolled annealed copper has grain and if run horizontally in the flex area, may split or fracture leaving the engineers an intermittent issue to try to find which is very frustrating and difficult to identify. It’s best to route traces at a 90 degree angle through the flex area and then make the necessary direction changes to accommodate the final design.

The only other big change to keep in mind is that angles in flex are not preferred. So the miter tool on your design software should be set to round instead of angular while you layout the flexible circuit design. The natural flexibility affects the transition from horizontal to vertical trace routing so we like to make that transition as seamless as possible. Rounded corners give us that luxury.

 

Conclusions

So as you can see the tactics for flexible circuit design don’t differ much from that of traditional PCBs. All of the typical specifications still apply and we add a few more things that require special attention. Cover layers require bigger openings than traditional solder mask, trace directions matter in the “flex areas” and miters should be round instead of angular. You may use all of the same CAD tools for design and output Gerbers as you would for any PCB. The documentation is all the same also with fabrication and assembly drawings being the norm.

So go ahead and attack your next flexible circuit design with the same confidence you have with PCBs. Of course if questions still arise you may always count on your supplier for quick and accurate support.

The Nobel Prize for Physics goes to Inventors of the LED

October 7, 2014 in Industry News

STOCKHOLM (Reuters) – Japanese scientists Isamu Akasaki and Hiroshi Amano and American Shuji Nakamura won the 2014 Nobel Prize for Physics for inventing a new energy efficient and environmentally friendly light source, the LED, the award-giving body said on Tuesday.

“With the advent of LED lamps we now have more long lasting and more efficient alternatives to older light sources,” the Royal Swedish Academy of Sciences said in a statement awarding the 8 million Swedish crown ($1.1 million) prize. Read more:

Printed Circuit Boards:  A Mobile Market

Printed Circuit Boards: A Mobile Market

October 6, 2014 in Uncategorized

Glass fiber/epoxy prepregs have dominated the mammoth PCB market for decades. Will that continue in a time of great change?

 

Glass fiber/epoxy laminates have been the foundational structural substrate in printed circuit boards (PCBs) for decades. These iconic thin, green “cards” support the transistors, resistors and integrated circuits at the heart of almost all digital technologies and connect them electrically via conductive pathways etched or printed on their surfaces. They are the world’s largest market for glass fiber, says Drew Walker, CEO of specialty glass fiber producer AGY (Aiken, S.C.). Indeed, market research firm Lucintel (Irving, Texas) reports a global market for glass fiber in PCBs of 844 million lb in 2013 and forecasts a compound annual growth rate (CAGR) of 4.5 percent. At that rate, the use of glass fiber in the PCB market will reach 1.1 billion lb by 2019. The growth will be fueled by the proliferation of mobile devices and digital control in appliances and cars, and new robotic applications in medical, defense and other manufacturing industries.  Read more:

Six Design Mistakes PCB Designers Can Avoid When Designing Printed Circuit Boards

October 3, 2014 in Uncategorized

These suggestions were introduced to me over 35 years ago and they are still valid today!

John Talbot  Tramonto Circuits LLC

6 Mistakes PCB designers can avoid when designing printed circuit boards

By Terry D Kozlyk, P.Tech.(Eng.) C.I.D.

TECH LAND HAS NOT BEEN the easiest place to work in these past two decades. I feel very fortunate to have practiced my way to better PCB design with several quality-minded companies, or linchpins, as marketing guru Seth Godin would say.

I say fortunate because I have worked for several large multi-nationals with a structured process and process documents. Others have been small technology startups, where you have to make do with many aspects of PCB design such as limited time, limited money and limited resources. Some PCB design environments shared similar practices whereas others developed their own according to what worked well for them. Read more:

 

Request A Quote

Please attach your documents and describe quantities required. We’ll contact you within 24 hours with any questions or a formal quotation.